Skip to Content
+32 15 62 70 80 info@ecowatt.be Mon-Thu 07:30-17:00, Fri 07:30-13:30 Request a repair
Repair
Buderus Fault code Buderus
6L

Flame goes out during operation

Breakdown: the boiler is stopped

While the burner is running, the boiler loses the flame signal. It tries to restart by itself; if the flame is lost too often, it locks out for safety.

What you can do

  1. Write down the code shown, the number next to it if there is one, and the boiler model (on the rating plate).
  2. Reset the boiler once only.
  3. If the code comes back, do not keep trying and do not take anything apart: call us.

Does your boiler show 6L?

Repair visit: 180 € excl. VAT (190.80 € incl. 6 % VAT*), first hour included, parts excluded.

* 6 % VAT: work on a private home more than 10 years old, invoiced to a private person. Without a written objection within a month of the invoice, you confirm that these conditions are met; otherwise the VAT is 21 % and the responsibility is yours.

Buderus

Choose a real expert

Ecowatt is an approved Buderus System Partner: factory training in Germany, direct access to spare parts, one contact.

The variants of code 6L

The small number shown beside the code tells which.

6L
229

No ionisation signal during burner operation

Breakdown: the boiler is stopped GB072, GB162, GB172, GB172i
6L
513

Flame loss during the post-ignition time

Blocking: it retries by itself KB195i, KB195i.2
6L
514

Flame failure during the stabilisation time

Blocking: it retries by itself GB212, KB192i, KB192i.2
6L
515

Flame failure during 1st + 2nd stage operation

Blocking: it retries by itself GB212, KB192i, KB195i, KB195i.2
6L
516

Flame loss when switching to 1st stage

Blocking: it retries by itself KB195i, KB195i.2
6L
517

Flame loss during 1st-stage operation

Blocking: it retries by itself KB195i, KB195i.2
6L
518

Flame loss when switching to 1st and 2nd stage

Blocking: it retries by itself KB195i, KB195i.2
6L
548

Too many restarts

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
553

Too many flame losses

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
555

Flame failure during ignition gas stabilisation

Blocking: it retries by itself GB212, KB192i, KB192i.2
6L
561

Voltage interrupted during burner start

Breakdown: the boiler is stopped GB212, KB192i, KB192i.2, KB195i, KB195i.2
6L
587

Flame failure during part-load stabilisation

Blocking: it retries by itself GB212, KB192i, KB192i.2
6L
615

Flame loss during 1st and 2nd stage operation

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
616

Flame loss when switching to 1st stage

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
618

Flame loss during the change-over to 1st + 2nd stage

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
670

Flame loss during the safety time

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
671

Flame loss during the safety time

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
672

Flame loss during 1st-stage operation

Breakdown: the boiler is stopped KB195i, KB195i.2
6L
XXX

Too many burner start attempts

Blocking: it retries by itself GB212, KB192i, KB192i.2

The boilers that show this code

What our technician checks

  • The gas supply (dynamic pressure, tightness) or the oil supply
  • The monitoring electrode: wiring, connector, dirt and position
  • The flame current, read on the control module
  • The ignition (relay test) and the ignition device: wear, damage, electrode gap
  • The burner setting, according to its settings table
  • The air supply and the flue (blockage), and the pressure switch
  • The blocking fault memory, to see when the flame is lost
  • The connection of the first-stage and second-stage solenoid valves
  • Oil boilers: the flame sensor, the nozzle, the preheater shutoff valve and the mixing system
  • Dirt buildup in the boiler and, on room-sealed units, the tightness of the flue (CO or CO2 in the fresh air)
  • The power supply, if the burner control unit was switched off several times at startup

The same fault on other boilers

Recent boilers show alone the number older ones show beside the code.

229

Related codes

From the manufacturer's service manuals for Belgium. Each appliance has its own features: if in doubt, call us.